Indonesia Open 2020 Rules

21 Desember 2019 11:29 | Informasi Umum

Race Class & Format

RACE CLASS

·         2WD 3500KV , 4WD 3500KV, 2WD Modified, 4WD Modified  Pan Car Modified

RACE FORMAT

Qualifying

·         There will be Pre-Qualify plus THREE qualifying runs for each class.

·         Each run will last 5 minutes.

·         For the Pre-Qualify run, the starting grid will be staggered in a random order.

·         For the First Qualify, the starting grid will be based on Pre-Qualify best 3 laps.

·         For the second to third qualify, racers will be re-shuffled each rounds into heats based best lap time results

·         The starting order for each run will be based on the number of laps run in the time allowed.

·         Top Qualifier (TQ) will be awarded to the racer with the highest lap count for a single heat. 

Mains

·         All other classes Triple A Main 8 minutes, Two Main 5 Minutes for others. No bump up.

·         Triple A-Mains will be held for each class.

·         A Triple A-Main consists of three Mains.  Each Main will be 8 minutes in duration.

·         If a driver wins the first two Mains that driver must seat out the third Main.

·         The best two out of three Mains will count with the first tiebreaker being the finishing position of the best round lap time.


 

·         If second tiebreaker being the finishing position of the best second round lap time.

-          Fastest driver in each round will score: 100 points

-          2nd fastest will score: 98 points

-          3rd fastest will score: 97 points

-          4th fastest will score: 96 points

-          And so on, scoring one point less for each driver down to last qualifying position.

 

·         If a driver does not start a heat, he receives no points.

·         In each round, in case of a tie, the points will be equally awarded to each driver with the same lap and time score.

·         The first driver not in the tie will score points according to their position in the qualifying list.

 

-          For example:

-          Fastest driver 31 laps 8:03.00 will score 100 points

-          2nd place driver 31 laps 8:05.00 will score 98 points

-          3rd place driver 30 laps 8:01.00 will score 97 points

-          4th place driver 30 laps 8:04.00 will score 96 points

-          5th place driver 29 laps 8:01.00 will score 95 points - TIED

-          6th place driver 29 laps 8:01.00 will score 95 points - TIED

-          7th place driver 29 laps 8:01.00 will score 95 points – TIED

-          8th place driver 28 laps 5:04.00 will score 92 points

 

·         The discarded scores, laps and times will not be used to separate a tie. The driver with the highest single points score from the scores added will be awarded the tied position. In the case of a continuing tie, the next best scores will be considered. All best scores will be considered until the tie is broken. If a comparison of points fails to break the tie, the laps and times from the highest points will be compared. The driver with the fastest time from their highest score will be awarded the tied position.


 

Technical Specification

2WD 3500KV

Chassis:
Kyosho Mini-Z Racer MR01, MR015, MR02, MR03, Jomurema, PN Racing PNR2.5W and GLR

90mm-98mm wheel base only.

Body:
Kyosho Mini-Z, TRP Scale and Jomurema GT01 body only, Le Mans body and Lexan body NOT allowed, full windshield and window must be installed, except for clearance, Lexan window and Lexan Roof allowed.

Motor:

Allowed your own sensorless brushless motor 3500kv motor (PN Racing, Atomic, GL-Racing, DXR Unlimited)

The motors are to be run as is. Any tampering with the motor will result in disqualification. If any Race official suspects motor tampering, the driver will be subject to disqualification. Each class drivers can buy one more extra motor. change motor connect wire allowed.

The motors will be checked and KV tested by official and sealed. If the motors run without sealed will be disqualified.

Open Gear ratio.

ESC:
OPEN

Battery:

3500kv motor allowed to use any battery maximum 8.4 volt

Additional battery for transponder allowed.

Option Parts:

Any aftermarket brand Mini-Z production parts allowed, any homemade parts, 3D print parts and prototype parts not allowed.

Wheel:

All brand Plastic and Aluminum Mini-Z production wheel rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 21mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel and 3D print wheel not allowed.

Tire:

Any Brand of Rubber Mini-Z production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. No traction compounds allowed on tire or on race surface. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution. If a driver uses tire cleaner that has been deemed illegal, the driver will be subject to any penalties that apply. Please address any questions concerning tire cleaners at the drivers meeting.

 

4WD 3500KV Class

Chassis:
Kyosho Mini-Z Racer AWD MA010 and MA020, Atomic AMZ, BZ, SZ, GL Racing GLA, Mini-Q Q7, Xpower IMT, WL

No weight limit.

Body:
Lexan Touring Body wheelbase 98mm

Motor:
Allowed your own sensorless or sensored brushless motor 3500kv motor (PN Racing, Atomic, GL-Racing, DXR Unlimited, Team Power, Ensotech)

The motors are to be run as is. Any tampering with the motor will result in disqualification. If any official suspects motor tampering, the driver will be subject to disqualification. Each class drivers can buy one more extra motor. change motor connect wire allowed.

The motors need to be scruted by official and sealed,

ESC:
Open any ESC

Battery:
Any battery maximum 8.4 volt
Additional battery for transponder allowed.

Option Parts:
Any aftermarket brand Mini-Z production parts allowed, any homemade parts, 3D print parts and prototype parts not allowed.

Wheel:
All brand Plastic and Aluminum rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 21mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel and 3D print wheel not allowed.

Tire:
Any Brand of Rubber Mini-Z Racer production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. No traction compounds allowed on tire or on race surface. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution. If a driver uses tire cleaner that has been deemed illegal, the driver will be subject to any penalties that apply. Please address any questions concerning tire cleaners at the drivers meeting.

 

2WD Modified Class

Chassis:

Kyosho Mini-Z Racer MR01, MR015, MR02, MR03, Jomurema, GL Racing GLR and PN Racing PNR2.5W

Body:

Kyosho Mini-Z, TRP Scale and Jomurema GT01 body, Le Mans body NOT allowed, full windshield and window must be installed, except for clearance, Lexan window and Lexan Roof allowed. No lexan body allowed

Motor:

Can be use any model brush or brushless motor

ESC:

Open any ESC

Battery:

Any battery maximum 8.4 volt

Additional battery for transponder allowed.

Option Parts:

Any aftermarket brand Mini-Z production parts allowed, any homemade parts, 3D print parts and prototype parts not allowed.

Wheel:

All brand Plastic and Aluminum rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 21mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel and 3D print wheel not allowed.

Tire:

Any Brand of Rubber Mini-Z Racer production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. No traction compounds allowed on tire or on race surface. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution. If a driver uses tire cleaner that has been deemed illegal, the driver will be subject to any penalties that apply.

 

4WD Modified Class

Chassis:
Kyosho Mini-Z Racer AWD MA010 and MA020, Atomic AMZ, BZ, SZ, GL Racing GLA, Mini-Q Q7, Xpower IMT, WL

No weight limit.

Body:
Lexan Touring Body wheelbase 98mm

Motor:
Can used any model brushed and brushless motor

ESC:
Open any ESC

Battery:
Any battery maximum 8.4 volt
Additional battery for transponder allowed.

Option Parts:
Any aftermarket brand Mini-Z production parts allowed, any homemade parts, 3D print parts and prototype parts not allowed.

Wheel:
All brand Plastic and Aluminum rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 21mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel and 3D print wheel not allowed.

Tire:
Any Brand of Rubber Mini-Z Racer production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. No traction compounds allowed on tire or on race surface. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution. If a driver uses tire cleaner that has been deemed illegal, the driver will be subject to any penalties that apply. Please address any questions concerning tire cleaners at the drivers meeting.

 

Pan Car Mod Class

Chassis:

Open any 2WD or 4WD chassis, must be 94-102mm Wheel Base.

Body:

#600600 PN Racing Plastic Pan Car Body
#600800 PN Racing Lexan Pan Car Body
#600900 PN Racing Light Weight Lexan Pan Car Body 
#600810 PN Racing Lexan BMR Pan Car Body
#600810L PN Racing Lexan BMR Pan Car Body Light Weight
#SBRC-B001 Subrc Lexan Pan Car Body


Motor:

Can be use any model brush and brushless motor.


ESC:

Open any ESC

Battery:

Any battery maximum 8.4 volt

Additional battery for transponder allowed.


Option Parts:

Open any parts allowed (including homemade parts , 3D print parts and prototype parts)

Wheel:

All brand Plastic and Aluminum rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 21mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel and 3D print wheel not allowed.


Tire:

Any Brand of Rubber Mini-Z Racer production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. No traction compounds allowed on tire or on race surface. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution. If a driver uses tire cleaner that has been deemed illegal, the driver will be subject to any penalties that apply. Please address any questions concerning tire cleaners at the drivers meeting.

 

 WEIGHT, WIDTH & HEIGHT